Re: Disable Automated Floating Pool and Power on Policy
Thanks Mike. We have to shutdown our View 5.2 environment for electrical power upgrades on our data-center tonight. We will found out what happens when the pool and provisioning are both disable. Dave
View ArticleRe: ESXi 5 shows a datastore with no free space but it's empty
no, none of these worked.Weird as it was working fine till three weeks ago and nothing got changed. I will schedule an upgrade to 5.1 and see if I have better luck.
View ArticleRe-Using the same tile VMs for iterative testing - is this supported? Getting...
I configured a single partial tile, leaving out the standby VM, and the Microsoft Exchange VM. I had a successful end to end run on that tile. I then re-ran the harness a second time (note, in between...
View ArticleRe: VMware Ethernet with Cisco EtherChannel and Trunking Question
You and your network admin should follow the instructions described in these KB articles and not any others if you're unsure:VMware KB: Host requirements for link aggregation for ESX and ESXi VMware...
View ArticleRe: Can't see shared folders in Linux Guest (Windows Host)
So an update... I tried changing the two files in the link you gave. Reinstalled VMWare tools... I DO now have access to shared folders in /mnt/hgfs... THANK YOU! However, drag and drop still doesn't...
View ArticleHow many virtual processors or cores should I assign to my Guest OS in vmware...
Hi Here is my laptop's specs i7 Intel Quad Core 2.4 GHz, 16GB RAM, 1T drive, windows 8 I have to make a lab for my next exam. I need 4 guests on top of one guest on vmware workstation 9. All host and...
View ArticleRe: Re-Using the same tile VMs for iterative testing - is this supported?...
Did you staf ping or regular ping? The command would be "staf OlioDB0 ping ping" from a windows command prompt.
View ArticleRe: VMware Ethernet with Cisco EtherChannel and Trunking Question
1. Yes, edge trunk. This is a best practice for cSphere HA.2. You are fine with the Switchport command3. yep, dot1q to carry multiple VLANs.4. Yes, works fine across cards (of similar types).5. no, the...
View ArticleRe: Cloning PrimeClient to setup Client1-6 to support multiple tiles,...
The VMMARK2.CONFIG file is used by the VMmark harness to configure the benchmark run. The harness runs only on the prime client, so because your Client0 is the prime client, it's the only client that...
View ArticleRe: Cloning PrimeClient to setup Client1-6 to support multiple tiles,...
Only the prime client's VMMARK2.config file get's utilized.
View ArticleRe: Can't see shared folders in Linux Guest (Windows Host)
Okay, I just ran diff on the contents of the vmci.tar and vmhgfs.tar files in VMwareTools-9.2.2-893683.tar.gz (VMware Fusion 5.0.3) and VMwareTools-9.2.3-1031360.tar.gz (VMware Workstation 9.0.2) and...
View ArticleRe: Failed to join OU. Trying to join the domain without OU
During Mirage Migration process from Windows XP to Windows 7 the endpoint fails to join Domain specific OU. Failure results in error 2224 and domain join continues without placing computer account...
View ArticleRe: Disable Automated Floating Pool and Power on Policy
If you shut down the Connection Servers the VMs will also not be powered on. If you are bringing the entire environment down just bring down the CS cluster and View Composer first and then no View...
View ArticleRe: Re-Using the same tile VMs for iterative testing - is this supported?...
regular ping - what is the syntax for a staf ping. I see it also says to make sure the staf process is running. How would I check that and if it is not running, how do I start it?
View ArticleRe: Service starts and then stops during SRM 5.1.1 install
Hi, You must create 64-bit DSN for SRM 5.1. Michael.
View ArticleClik here to view.
Re: ESXi 5.1 U1 - Primergy RX200S4, Raid0 issue - VD not detected properly
Got it... I learned that ESXi does not support software RAID. There isn't any other way to make it work? Raid 0 would have been really nice for a VMware home lab...
View ArticleRe: Trouble getting into VM using RDP with a NAT connection
I was able to RDP into a Windows Guest successfully via NAT in my lab. Could you please check the Firewall in your WinSer2008R2 VM and also check if RDP is enabled in the Guest OS?
View ArticleVSphere Installation Question
Hi All,I am in the process of building the following server:Case: Fractal Design Define R4 ATX Tower Case Black PearlPower Supply: Corsair Professional Series HX750 750W ATX Fully Modular 80PLUS Gold...
View ArticleRe: Can't see shared folders in Linux Guest (Windows Host)
However, drag and drop still doesn't appear to be working. In the current build I have based on VMwareTools-9.2.2-893683.tar.gz I can DnD from Linux Mint 15 to the Host but not from the Host to the...
View ArticleRe: Re-Using the same tile VMs for iterative testing - is this supported?...
The command would be "staf OlioDB0 ping ping" from a windows command prompt.You can look in the task manager for STAFproc.exe.If it isn't running, you can log into your DS2DB0 via ssh and execute the...
View Article